Black Friday 2025!

Billet Front Upper Brace VEKTA.5 [KV6617]

New version 2 factory upgrade T6061 front billet upper Brace with quick access to the center drive shaft shaft screw. Conveniently service the center drive shaft without having to remove the brace, hinge pins etc. Now in the new gloss silver anodized finish

$54.99

METAL TRANSMISSION COVER VEKTA.5 [KV6140]

Replacement aluminum cover for the VEKTA.5 transmission. Mounting hardware is included (Not shown)This product has replaced KV2232

$24.99

Sold out

Hardened Steel Bevel Gears Set VEKTA.5 & VESLA.5 [KV6142]

These High-performance and precision CNC Hardened Bevel Gears are super tough and rated to be four times stronger than stock powder metal ones. They are a highly recommended upgrade if you want to bullet-proof your differentials. VEKTA.5 requires two sets to complete, one set for the VESLA.5. The material is SCM (Composite Steel) and Heat treated to HRC40-45 for extra strength. CNC machining allows for precise gear tooth profiles and tolerances. Heat treatment increases the hardness and strength of the gears. These gears are often used in high-performance applications.

$44.99

View product

VEKTA.5 & VESLA.5 Pull Tabs for Hook Pin (set of 4) [KV4440]

$3.84

Brushless Motor Mounting Hardware Set [KV9924]

Hardware set for mounting Hobbywing Motor KVS518 - M4 Countersunk Washers - 4pcs KV3364 - FH4x16mm - 4pcs

$5.99

VEKTA.5 & VESLA.5 CV Drive Shaft Hub Pin set of 2 [KV9909]

Set contains part numbers: KV5503, KV5520

$8.79

Taylor Billet Vesla, Vekta.5 & KV5TT Steering Servo Mount kit

A stunning billet servo mount kit for your Kraken Vesla, Vekta or Trophy Truck model. Simply trim off the plastic lugs from the side of the stock plastic battery tray and then use our billet mounts to bolt directly to the holes pre-made in the chassis to remove all flex! These will also fit Losi 5IVE 1.0 and 2.0 models. You will need to trim the stock steering servo mount from the radio tray but it will fit right on the chassis in factory mounting points to give your servo a sturdy mounting system. Special note: Those with the VEKTA.5E and those using the Kraken brand conversion kit will need to modify these mounts to fit by shortening the mounts approximately 10mm. We suggest taking off 5mm from the top and bottom of the mounts to do this.

$39.95

Big Bore VESLA.5 Transmission Case [KVS206]

The VESLA Big Bore Transmission is the no-compromise upgrade for the highest power builds. To accommodate for the power of brushless and big bore gas builds this case features the following benefits: Massive idle gear for improved strength Precise billet machined transmission halves Compatible with both Gas and Electric VESLA models. Included with this upgrade: Machined aluminum transmission case Idle gear bearings Hardware Spacer for Electric build Shaft sleeve To complete this case you will need to purchase separately: Big Bore Hardened Gear set for VESLA KVS220 A layshaft suitable for your application Layshaft Options: Depending on your gear setup and power system you will need to purchase the correct layshaft. For a GAS build you will want to choose from the following: KVS163 Slipper Eliminator; lightest weight direct drive system. Uses the factory Kraken brand of gear KVS161 Gas Big Bore Layshaft; this is used for a slipper clutch setup for the Kraken brand of gear TAY5121 Taylor RC Blackbone Gas Layshaft; this gives you the option for using Blackbone optional gear sets. For an ELECTRIC build you will want to choose from the following: KVS164 Slipper Eliminator; lightest weight direct drive system. Uses factory Kraken brand of gears KVS146 Electric Big Bore Layshaft; this is used for a slipper clutch setup for the Kraken brand of gear BBR5126 Taylor RC Blackbone Electric Layshaft; this gives you the option for using Blackbone optional gear sets Note: It is highly recommended that you use the hardened gears only. If you already have the standard transmission case hardened gear set you only need to purchase the KVS213 Big Bore idle gear Download Set-Up Diagram HERE IMPORTANT: For your exhaust pipe to clear the transmission case for smaller bore engines, you’d need a curved-up exhaust header like the Taylor RC Exhaust pipe: TAY5160

$179.99

12S VESLA.5 Battery Plate with straps [KVS219]

This battery plate is an upgrade for those with an original 8S RTR VESLA model that want to upgrade to the 12S Spec or just want a battery tray that is easier to install different sized batteries. This is also a good option to have for customers that are converting their gas VESLA to Electric. Take your older 8S VESLA into a 12S monster with this battery plate combined with Hobbywing's MAX5 G2 EZRUN Combo The battery plate is easy to install and features six stand-off lugs for the Velcro straps. It is made of T6061 aluminium and anodized black. This is the standard included piece for the VESLA 12S models.

$54.99

Metallic brace with 'KRAKEN' branding on a white background

HD Billet Aluminum T6061 Top Brace VESLA.5 [KVS201]

Optional T6061 billet part to replace the stock plastic version.

$29.99

Hardened Steel Transmission Gears Set with Taylor idler gear VESLA.5 [KVS218]

Specially made for Big Bore engines applications and 12S using the stock style gearbox, these High Performance CNC Hardened Steel Transmission Gears are precision cut for high power use. This new V2 set includes the proven Taylor HD Idler Gear Coupled with our CNC Hardened Bevel Gears (KV6142), you are all good to go with a strong and bulletproof set-up for your Big Bore applications!

$109.99

VEKTA.5 Air Filter Sponge Set [KV2257]

Set contains part numbers: KV4424, KV4432

$9.89

Kraken RC Maxxis Trepador Tire Set V2 [KV6109]

UPDATED for 2024, the V2 uses new stiffer compound to minimize wear and tear on the bead locks area. The new stiffer compound makes the tire more durable overall. Kraken Maxxis Trepadors Tires are a collaboration project between Kraken RC, MAXXIS Tires and Levi Shirley. These scale tires are modeled after the 1:1 tires driven by Levi Shirley in the Ultra4 race circuit. They are high performance off road tires with aggressive threads for extreme grip. These off road scale tires are the first of their kind for the 1/5th scale RC platform and they compliment the VEKTA.5 or the VEKTA.5LSE very well. Tires measure 222mm (approximately 8 3/4") in height and 74mm (approximately 2.9") in width. They are compatible with truck sized 1/5th scale wheels. These tires are L & R directional and requires foam inserts - KV6110. Warranty: There is no warranty as tires are considered wear and tear items. By purchasing these tires, you are agreeing to these terms.

$45.99

VESLA.5 HD Rear Billet Aluminum Arms [KVS216]

Upgraded billet rear arms for the VESLA.5. We highly recommend using our ultimate titanium hinge pins in conjunction with these arms: KVS212

$149.99

Kraken Maxxis Trepador Tire Inserts V2 [KV6110]

Updated for 2024. These V2 inserts are now three times lighter compared to the previous ones. HD tire inserts for Kraken MAXXIS Trepadors Tires. Made of heavy duty plush material specifically engineered for the MAXXIS tires. They provide the right density and stability for the tall tires. Designed to take heavy abuse in mind and help the sidewall from collapsing during high speed turns. Sold in a set of two.

$39.99

Kraken VESLA.5/TSK-b/SX5 Braces Set [KRC700]

$24.95

VEKTA.5 Front Arm Set [KVT02]

Set contains part numbers: KV8806, KV8807, KV8808

$24.99

Sold out

Kraken VESLA.5 Front or Rear Sway Bar Kit [KVS158]

VESLA.5 sway bar kit fits directly on the rear. For front use, shorten each side by approximately 18 mm.

$37.99

View product

HPI Baja Hardened Steel Bevel Gears Set [KRC90021]

Precision-hardened steel CNC gears. These Super-Duty gears are at least three times stronger than your stock. If you run big bore engines or want a bulletproof diff setup, these gears will exceed all expectations. Replaces HPI part #87567.

$49.99

Carbon Fiber Brake Disk VEKTA.5 & VESLA.5 [KV6151]

This Carbon Fiber brake disc option fits both VEKTA and VESLA. Its heat-resistant properties prevent binding. A great upgrade that increases the stopping power on your rigs.

$21.99

VEKTA.5 F/R 13T Differential Pinion Gear [KV5545]

VEKTA.5 F/R Differential Pinion Gear, 13T

$19.99

Spindle Screws and Lock Washers Set [KV9921]

Screws and lock washers replacement set for spindle carriers. Fits VEKTA.5/TT/E KV3351 - BH6X18mm - 4 pcsKV3455 - M6 Lock Washer - 4 pcs

$6.99

Kraken VESLA.5 Clipring Set [KVS124]

Stock replacement set for the VESLA.5.

$4.99

VESLA.5 HD 7075 Billet Steering System [KVS227]

Our newest upgrade for the VESLA is one of performance and style. This steering rack system is machined from tough 7075 billet aluminum. The drag link is finished with a set of pre-installed bearings ensuring smooth operation and minimizing play. The servo saver maintains adjustability with the factory spring and collar and has a nice cam profile keeping your servo from being damaged in a hard impact. These are a direct fit and require no modifications.

$99.95

Jar of silicone oil with a label indicating '1,000,000 cSt' on a white background

Kraken Silicone Differential Oil 1M CST (50cc) [KV9919]

Upgrade 1 million weight CST Silicone Diff Oil for Kraken VEKTA.5 and any other RC models with sealed differnetials. Made in Japan 50cc

$15.99

VEKTA.5 Long R-Pin Body Clip [KV5506]

$0.99

VESLA.5 HD Front Billet Aluminum Arms [KVS215]

Upgraded billet front arms for the VESLA.5. We highly recommend using our Ti hinge pins in conjunction with these arms - KVS212 Disclaimer: Using these arms without the reinforcement from the Skid plate may cause breakage in a bad crash. We highly recommend you install the VESLA Skid plate - KVS223

$149.99

Billet Aluminum HD VESLA.5 Center Brace [KVS217]

Center Brace and Chassis Stiffener for VESLA.5 (Electric Only). Super heavy duty, all parts are made out of billet aluminum. Center rod is 16mm in diameter! This is a standard included upgrade on the Kraken VESLA.5 12S models. If you have an older 8S VESLA or you are converting your gas model to electric then this is a must have upgrade!

$69.99

Billet Aluminum HD VEKTA.5 Front Differential Case [KV6107]

CNC T6061 Billet Aluminum Front Diff case for the VEKTA.5. Designed to take heavier loads with oversized pinion bearings (10x26x8mm) and comes complete with bearings. This is the updated gloss silver finish.

$139.99

VEKTA.5 Gas Tank Set [KV2252]

Set contains part numbers: KV8839, KV8840, KV4413, KV4417, KV4423, KV8841, KV8842, KV4402, KV3309, KV3310, KV3311, KV3312, KV3339, KV3380

$59.99

Ultimate Titanium Hinge Pins Set for the VESLA.5 [KVS212]

Our popular upgrades for the HPI Baja is now made available for the VESLA.5. Titanium GR.5 provides the ultimate strength and durability. Easy removal with captured screws on one end makes changing out your arms a breeze. Our Ti. Hinge Pins set is theultimate upgrade for those looking for the best of the best.

$74.99

Kraken VESLA.5 Spur Gear Cover [KVS105]

Stock replacement part for the VESLA.5.

$10.99

HD Extended Dogbones kit for X2E A-Arms for HPI Baja [KRC90001]

Kraken RC HD Dogbones kit is specially designed for our X2e (extended) Rear Lower Arms. Made out of hardened steel, they are super tough. At 8.6 mm in diameter, our dogbones are the toughest with unmatched quality, fit and finish. Cross pins are replaceable and are considered as wear and tear components. Works with stock 22mm HPI drive cups. High quality grease is highly recommended when running our dogbones kit. Compatible with HPI Bajas that use the 22mm standard sized diff cup (Not the 25mm Super Heavy Duty HPI style cup). If you have a 2014+ Baja 5B SS or newer SBK those use a 25mm 5SC style diff cup. The X2E kraken dogbones use the 22x4mm pins. you will need the 22x4mm style drive cups OR different extended dogbones with the 5SC size (25x4.5mm) Features: Hardened Steel with Black Oxide. Replaceable cross pins with set screws. Technical Specs DogBone: Length - 161 mm (Extended) Material - SCM435 Hardness - HRC54 Color - Black Oxide Cross Pin: Size: 4x22mm Material: SUJ2 Hardness: HRC65 Color - Black Oxide

$32.99

VEKTA.5 F/R Drive Shaft CV Set [KV2223]

Set contains part numbers: KV5503, KV5515, KV5518, KV5520, KV3392. This set is for us on the front CVD of the Kraken VEKTA.5 Buggy and the rear CVD of the original V1 and V2 Rear Solid Axle set-up. If you have the V3 style rear axle use the KV2275 Paddle Style Rear Driveshaft

$24.99

VEKTA.5 Front Shocks Silicone Oil 250 CST [KV9915]

Stock front replacement Shock Oil for the VEKTA.5 - 250 CST.Content: 100cc Silicone Shock Oil. Enough for 2 front shocks build. Pure Silcione Shock Oil. Made in Japan.

$11.99

VEKTA.5/TT Center/Rear Joint Screw Pin V2 [KV9918]

For use on stock VEKTA.5/TT. Also for use in in the upgraded rear CVD Driveshaft kit KV6127

$7.99

VEKTA. 5 Flat Washer Set [KV9907]

Set contains part numbers: KV3387, KV3362, KV3383, KV3401, KV3380, KV3385, KV3381

$6.99

TAYLOR Billet VEKTA/KV5TT Front Diff Housing

This show-stopping Kraken Billet Diff Housing will add supreme support for your front Differential gears to ensure long life even with our huge HP Big bore engines. Features: Oversize pinion gear support bearings (supplied) A stylish Billet Anti-Roll bar bracket (supplied with hardware) Allows fitment of either the stock shock tower or our Billet 7075 Vekta and KV5TT towers. Supplied with Stainless fitting hardware.

$199.75

Sold out

Beast RC Billet HD Kraken Vertical Braces

This pair of Precision CNC Vertical braces are way thicker than stock, machined from a 10mm Billet but then pocketed out for low weight and super strong! Made for all modern Vektas and All TT Trucks with 8mm shock mount bolts.The Kraken Vekta and Vekta TT are both solid heavy cars, so need good strength in this area in case of impact loading.

$149.99

View product

HD Rear upper Links With Heim Joints Set [KV6152]

We are proud to Introduce the all-new HD Rear Upper Links With Heim Joints Set for our VEKTA.5, E and TT. A bulletproof set-up for your rigs. Set it and forget it! What is included: 1 set Aluminum lower links set 4 Sets of High-Grade Stainless Steel Heim Joints 8 Machined Spacers for Heim Joints

$59.99

Big Bore Hardened VESLA.5 Gears Set [KVS220]

This newly redesigned, stronger Idler gear was added for Big Bore power engine use. It is highly recommended when running more powerful engines. The larger idler gear includes two 20x32x7mm bearings. This gear set can also be used for 12S Brushless electric along with the new larger Big Bore Transmission case

$129.99

VEKTA.5 Super Duty Stiff Rear Springs Set [KV6146]

These are the Super-Duty extra-stiff spring rears set for the VEKTA.5 Gas, VEKTA.5TT and Brushless VEKTA.5E Ultra. They are new and 4mm thicker in diameter than the stock 3.2 mm.

$24.99